Aspect used for input must follow the same rules as aspect computed in other GRASS programs (see v.surf.rst or r.slope.aspect).
Flowline output is given in a vector map flout, (flowlines generated downhill). The line segments of flowline vectors have endpoints on edges of a grid formed by drawing imaginary lines through the centers of the cells in the elevation map. Flowlines are generated from each cell downhill by default; they can be generated uphill using the flag -u. A flowline stops if its next segment would reverse the direction of flow (from up to down or vice-versa), cross a barrier, or arrive at a cell with undefined elevation or aspect. Another option, skip=val, indicates that only the flowlines from every val-th cell are to be included in flout. The default skip is max(1, <rows in elevin>/50, <cols in elevin>/50). A high skip usually speeds up processing time and often improves the readability of a visualization of flout.
Flowpath length output is given in a raster map lgout. The value in each grid cell is the sum of the planar lengths of all segments of the flowline generated from that cell. If the flag -3 is given, elevation is taken into account in calculating the length of each segment.
Flowline density downhill or uphill output is given in a raster map dsout. The value in each grid cell is the number of flowlines which pass through that grid cell, that means the number of flowlines from the entire map which have segment endpoints within that cell. With the -m flag less memory is used as aspect at each cell is computed on the fly. This option incurs a severe performance penalty. If this flag is given, the aspect input map (if any) will be ignored. The barin parameter is a raster map name with non-zero values representing barriers as input.
The values in length maps computed using the -u flag represent the distances from each cell to an upland flat or singular point. Such distances are useful in water erosion modeling for computation of the LS factor in the standard form of USLE. Uphill flowlines merge on ridge lines; by redirecting the order of the flowline points in the output vector map, dispersed waterflow can be simulated. The density map can be used for the extraction of ridge lines.
Computing the flowlines downhill simulates the actual flow (also known as the raindrop method). These flowlines tend to merge in valleys; they can be used for localization of areas with waterflow accumulation and for the extraction of channels. The downslope flowline density multiplied by the resolution can be used as an approximation of the upslope contributing area per unit contour width. This area is a measure of potential water flux for the steady state conditions and can be used in the modeling of water erosion for the computation of the unit stream power based LS factor or sediment transport capacity.
The program has been designed for modeling erosion on hillslopes and has rather strict conditions for ending flowlines. It is therefore not very suitable for the extraction of stream networks or delineation of watersheds unless a DEM without pits or flat areas is available (r.fill.dir can be used to fill pits).
To label the vector flowlines automatically, the user can use v.category (add categories).
1. Construction of flow-lines (slope-lines): r.flow uses an original vector-grid algorithm which uses an infinite number of directions between 0.0000... and 360.0000... and traces the flow as a line (vector) in the direction of gradient (rather than from cell to cell in one of the 8 directions = D-infinity algorithm). They are traced in any direction using aspect (so there is no limitation to 8 directions here). The D8 algorithm produces zig-zag lines. The value in the outlet is very similar for both r.flow and r.flowmd (GRASS 5 only) algorithms (because it is essentially the watershed area), however the spatial distribution of flow, especially on hillslopes is quite different. It is still a 1D flow routing so the dispersal flow is not accurately described, but still better than D8.
2. Computation of contributing areas: r.flow uses a single flow algorithm, i.e. all flow is transported to a single cell downslope.
"ERROR: r.flow: " input " file's resolution differs from current" region resolution
The resolutions of all input files and the current region must match.
"ERROR: r.flow: resolution too unbalanced (" val " x " val ")" The difference in length between the two axes of a grid cell is so great that quantization error is larger than one of the dimensions. Resample the map and try again.
Original version of program:
Maros Zlocha and Jaroslav Hofierka, Comenius University, Bratislava,
Slovakia,
The current version of the program (adapted for GRASS5.0):
Joshua Caplan, Mark Ruesink, Helena Mitasova, University of Illinois
at Urbana-Champaign with support from USA CERL.
GMSL/University of Illinois at
Urbana-Champaign
Mitasova, H., L. Mitas, 1993, Interpolation by regularized spline with tension : I. Theory and implementation. Mathematical Geology 25, p. 641-655. (online)
Mitasova and Hofierka 1993 : Interpolation by Regularized Spline with Tension: II. Application to Terrain Modeling and Surface Geometry Analysis. Mathematical Geology 25(6), 657-669. (online)
Mitasova, H., Mitas, L., Brown, W.M., Gerdes, D.P., Kosinovsky, I., Baker, T., 1995: Modeling spatially and temporally distributed phenomena: New methods and tools for GRASS GIS. International Journal of Geographical Information Systems 9(4), 433-446.
Mitasova, H., J. Hofierka, M. Zlocha, L.R. Iverson, 1996, Modeling topographic potential for erosion and deposition using GIS. Int. Journal of Geographical Information Science, 10(5), 629-641. (reply to a comment to this paper appears in 1997 in Int. Journal of Geographical Information Science, Vol. 11, No. 6)
Mitasova, H.(1993): Surfaces and modeling. Grassclippings (winter and spring) p.18-19.
Last changed: $Date: 2006-12-13 08:10:28 -0800 (Wed, 13 Dec 2006) $
Main index - raster index - Full index
© 2003-2008 GRASS Development Team